Gå vidare till produktinformation
1 av 1

Athena-SCE

Athena Cut Ring Head Gasket Set, BMW N63/S63

Athena Cut Ring Head Gasket Set, BMW N63/S63

Ordinarie pris $399.99 USD
Ordinarie pris $389.99 USD Försäljningspris $399.99 USD
Rea Slutsåld
Frakt beräknas i kassan.
Bore Size - Thickness

Designed specifically for the BMW N63 and S63 V8 engine to replace BMW part numbers 11127567764 and 11127567765 of the F10/F11/F12/F13/F14/F15/F16/F01/F02 chassis. *** Will NOT work on F90 M5 S63 *** 

Factory OEM & MLS head gaskets are only engineered to handle a limited amount of cylinder pressures before they start to leak, causing a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure.

Athena-SCE Cut Ring Head Gaskets are uniquely designed to handle increased cylinder pressure caused by power modifications, making them the recommended choice for applications making 12+ psi.

Design:

Athena-SCE's gasket body is composed of Motorgasket, a reinforced material developed by Athena's R&D department. This consists of a steel core covered with two layers of asbestos-free aramid fibre and offers excellent thermal and mechanical resistance without compromising its ability to adapt to mating surfaces.

To ensure maximum sealing under all conditions, a silicone bead is also applied to critical sealing areas, such as oil and coolant passages. 

The AISI 304 stainless steel cooper rings bite into the aluminum head, providing maximum sealing around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2 bar boost.

Please be aware that the gasket should be 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm.

Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat.

Sold as a set - Includes Bank 1 and Bank 2 Gaskets

Installation instructions:

  1. Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant.

  2. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation.

  3. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions.

  4. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket.

  5. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed.

  6. It is recommended to not use any additional sealant on the MLX gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

BMW S63 Applications:

BMW M5 Series

2011 - 2016 BMW F10 M5

BMW M6 Series

2012 - 2018 BMW F12 M6
2012 - 2018 BMW F13 M6

BMW N63 Applications:

BMW 5 Series

2010–2017     BMW F07      550i
2011–2016     BMW F10      550i

BMW 6 Series

2012–2018     BMW F06     650i
2012–2018     BMW F12     650i    
2012–2018     BMW F13     650i

BMW 7 Series

2009–2015     BMW F01/F02     750i/750Li

BMW X5 Series

2014–2018     BMW F15     X5 xDrive50i

BMW X6 Series

2015–2019     BMW F16     X6 xDrive50i

Alpina B5 Series

2011–2016     BMW F10 Alpina     B5 Bi-Turbo

Alpina B6 Series

2012–2018     BMW F06/F12/F13 Alpina     B6 Bi-Turbo

Alpina B7 Series

2010–2015     BMW F01 Alpina     B7 Bi-Turbo

Lagerhållningsenhet:ATH-HG-CR-S63-905047

Visa alla uppgifter