Zu Produktinformationen springen
1 von 1

Wagner Tuning

Wagner Tuning Head Stud Kit, BMW N54

Wagner Tuning Head Stud Kit, BMW N54

Normaler Preis $449.99 USD
Normaler Preis $449.99 USD Verkaufspreis $449.99 USD
Sale Ausverkauft
Versand wird beim Checkout berechnet

BMW N54 Engine Pro-Series 18.8 Cylinder Head Stud Set

Replacing the original cylinder head screws with high-strength Pro-Series 18.8 studs is necessary when making large increases in performance, as the original cylinder head screws elongate during operation and the cylinder head can lift off.

The Pro-Series 18.8 stud bolts with a tensile strength of 1850 N / mm² provide a solution to this.

In addition, these stud bolts do not have to be replaced after dismantling, but can be reused.

Kit Contents:

Standard Kit

(4) M9 Stud Bolts
(10) M11 Stud Bolts
(4) M9 Nuts
(10) M11 Nuts
(14) Washers
Assembly Paste
Assembly Instructions

High Boost Kit**

(14) M11 Stud Bolts
(14) M11 Nuts
(14) Washers
Assembly Paste
Assembly Instructions

**High Boost Kit, it is a MUST to drill and tap the four outer 9mm holes in the engine block to increase their size to 11mm holes. This will ensure that all the engine block holes are uniform in size and can accommodate all 14x 11mm Studs. Additionally, it will help distribute even force across the cylinder head-gasket surface.

Tensile strength: PS 18.8 steel / 1850+ N/mm² (270.000+PSI)

A special steel is used which, after tempering, has a tensile strength of 1850 + N / mm².

All threads are formed and not cut as usual. The so-called rolling of threads can increase the strength of the tooth flanks by around 30%.

All Pro-Series products are supplied with a nickel coating or optional with a burnished protecting against corrosion in the long term, even under the toughest conditions. Pro-Series stud bolts have a hexagon socket drive on the head side for screwing in the stud bolts. Due to a cone on the engine block side of the bolt, these are not supported on the thread flanks when the nuts are tightened, but in the bore of the thread in the engine block. This support protects the threads when racing engines are frequently rebuilt.

Pro-Series advantage over other manufacturers is the nuts and washers included in the set, these also have a tensile strength of 1850 N / mm².

Application list:

From MY 2006 - 2012
335i E90/E91 Limousine/Kombi 306PS
335i E92 Coupé 306PS
335is E92 Coupé 326PS
335i E93 Cabrio 306PS
535i E60/E61 Limousine/Kombi (USA) 306PS
135i E82/E88 Coupé/Cabrio 306PS
135i E82/E88 Coupé/Cabrio 326PS
X6 35i E71 306PS
X6 35i E71 326PS
Z4 35i E89 306PS
Z4 35is E89 340PS
740i F01/F02/F03/F04 326PS
1er M E82 Coupé 340PS
Alpina B3 BiTurbo 360PS
Alpina B3S BiTurbo 400PS

Manufactured in Germany

Installation Instructions:

1. After unpacking ProSeries stud bolts, inspect all hardware prior to installation. Look for obvious defects or shipping damage. Contact our sales team immediately with any questions or issues.
2. Before mounting, compare the supplied bolts with the stock screws, paying particular attention to the thread type and length of the bolts.
Check existing threads inside engine block for damage. To ensure proper thread engagement and accurate torque readings, make sure that all threads are free from remnant sealer, lubricant, and debris. Check the flatness and surface finish of the engine block and cylinder head deck to avoid gasket failure.
3. Insert stud bolts into the engine block and tighten with a 5mm hexagon socket on the drive provided at the head of the stud bolt with a torque of 15Nm.
4. If the stud bolts are to remain permanently installed in the engine block, they can be used with screw lock (not included)
5. Attention! Before final mounting of Pro-Series nuts and washers, all contact surfaces must be completely wetted with the supplied special ProSeries lubricant.
If this will not be considered the applied tightening torque is falsified and the resulting clamping force is reduced. Under certain circumstances, this can also inevitably lead to the bolts breaking / shearing off.

6. Tighten nuts in three equal steps in the factory sequence. For the last pass, refer to the table shown below:

Thread Type
M9 x 1.25 1.25 Nm 2.45 Nm 3.65 Nm
M10 x 1.25 1.30 Nm 2.60 Nm 3.85 Nm
M11 x 1.125 1.40 Nm 2.80 Nm 2.80 Nm
M12 x 1.25 1.45 Nm 2.90 Nm 3.130 Nm

7. ProSeries studs and nuts can always be reused. When re-tightening or reassembling, please always ensure that all contact surfaces are wetted with special ProSeries lubricant. Please contact our sales team if you have any further questions.


Vollständige Details anzeigen