• ARP Main Stud Kit, BMW S58 - 5150 AutoSport
1 1

ARP Automotive Racing Products

BMW S58 ARP Main Stud Kit

BMW S58 ARP Main Stud Kit

$229.99 USD
$229.99 USD $229.99 USD
Распродажа Продано
Стоимость доставки рассчитывается при оформлении заказа.

This ARP Main Stud Kit is designed to replace BMW part number 11118604584 for the BMW S58 engines found in high-performance models such as G80/G81/G82/G83 M3/M4, X3M F97, and X4M F98. 

Upgrading from factory main bolts to ARP Main Studs is a simple, yet greatly beneficial upgrade. ARP Main Studs offer the following benefits: 

- Uniform Clamping Force: ARP Main Studs provide a uniform clamping force that OEM bolts cannot. With the improved distribution of pressure across main bearing caps comes better, more precise crank alignment for stability and longevity. 
- Improved Block Stability and Rigidity: ARP Main Studs improve block rigidity and therefore stability. This ensures maximum power transfer from the crank to the drivetrain, which in turn ensures: 
- Improved Throttle Response
- Greater Horsepower
- Higher Torque Output
- Prevent Main Cap Walk: This occurs as main caps shift and move out of position, which can cause crank and engine damage
- Reduced Risk of Fastener Stretching: Under high RPM applications and high loads, factory main bolts are prone to stretching and deforming. ARP uses advanced manufacturing techniques and high quality materials for hardware that is much less prone to deformation under load.
- Safeguard Engine Block Threads: Because ARP Main Studs have unmatched tensile strength, they are much less likely to deform or strip block threads under high loads. Additionally, ARP’s precision machining and manufacturing ensures that stud threads are both highly accurate and consistent.

 

When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best.

Installation Instructions: 
    1. Thoroughly clean all threaded holes in the engine block. If necessary, use an ARP thread chaser to ensure clean threads and proper engagement.
    2. Inspect all studs, nuts, and washers for damage and verify proper fit, length, and dimensions before installation.
    3. Install the main studs into the engine block by hand until snug. Do not overtighten.
    4. Install the main caps and check for proper fit, alignment, and any binding.
    5. Apply ARP Ultra-Torque Fastener Assembly Lubricant to the stud threads, nuts, washers, and washer contact surfaces.
    6. Install the washers and nuts and tighten them by hand. Do not substitute motor oil or other lubricants for ARP Ultra-Torque.

    7. Following the manufacturer's recommended main-cap tightening sequence, torque all main stud nuts progressively in three steps using ARP Ultra-Torque:

      Step 1: 20 ft-lbs
      Step 2: 40 ft-lbs
      Step 3: 60 ft-lbs

    8. After final torque, measure the main bearing bores and verify proper size, roundness, and alignment.
    9. If necessary, line hone the main bores with the ARP main studs installed and torqued to specification.
    10. Verify final main bearing oil clearances before engine assembly.

BMW S58 Applications:

2 Series

2023-Present     G87     M2

3 Series

2021-Present     G80     M3

4 Series

2021-Present     G82/G83     M4

X3 Series

2019-Present     F97     X3M

X4 Series

2019-Present     F98     X4M


ARP-MSK-S58

Просмотреть всю информацию