1 1

5150 AutoSport

5150 AutoSport Head Gasket & Head Stud Kit, BMW S65

5150 AutoSport Head Gasket & Head Stud Kit, BMW S65

$723.98 USD
$723.98 USD
In offerta Esaurito
Spese di spedizione calcolate al check-out.
Head Gasket Type - Bore - Thickness
Head Stud Kit

MLS Head Gasket:

The Cometic MLS Head Gasket is a high-quality gasket designed specifically for the S65 V8 engines found in BMW vehicles. This gasket is intended to replace the original BMW part #11127841560, and is designed to provide superior sealing performance compared to other gaskets on the market.

The gasket features a multilayer steel (MLS) construction, which provides increased strength and durability, as well as improved heat resistance and reduced cracking. This makes the Cometic MLS Head Gasket an ideal choice for those looking to upgrade or replace their existing head gasket on their S65 V8 engine. Additionally, the gasket is precision engineered to ensure a perfect fit, and is made from high-quality materials to ensure longevity and reliability.

The S65 factory head gaskets specifications are 92mm Bore with a thickness of 0.027 inches.

MLS Installation Instructions:

  1. Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant.

  2. Install the MLS gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation.

  3. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions.

  4. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket.

  5. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed.

  6. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

Head Stud Kit

Upgrade the performance of your BMW S65 engine with the ARP Head Stud Kit. This high-performance head stud kit is designed to replace the factory head bolts BMW# 11127838831 and ensure your engine can withstand the extreme conditions of high-performance driving.

Manufactured by ARP, a leader in fastener technology for high-performance engines, the ARP Head Stud Kit 201-4307 features a tensile strength of 200,000 psi. This ensures that the studs can withstand extreme pressure and loads, providing improved durability and reliability for your engine.

The ARP Head Stud Kit is a bolt-on kit that requires no additional modifications. It includes precision-machined washers and nuts, ensuring a perfect fit and easy installation. This kit is designed specifically for the BMW S65B40 engine, which can be found in various BMW models, including the M3 E90, E92, and E93.


Head Stud Kit Installation Instructions: 

1. To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if necessary with ARP Thread Chaser.
2. Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages, plus proper fit, length and dimension.
3. If the cylinder head studs protrude into a water jacket, lubricate the block threads of the studs with ARP THREAD SEALER.
4. Screw studs into the block “HAND TIGHT ONLY”.
5. Install the cylinder head(s) and check for binding or misalignment.
6. Lubricate the stud threads, nuts and washers with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
Then install the washers and the nuts onto the studs and tighten them hand tight.
ARP recommends using the ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT that is provided with each kit as opposed to motor oil. This is due to higher friction on the studs as well as inconsistencies in the clamping force of the fasteners when motor oil or other low quality lubricants are used.

PRELOAD (TORQUE) RECOMMENDATIONS

7. Following the manufacturers recommended torque sequence tighten the nuts steps 1-4

Step 1: Tighten Studs 1 through 10 to 25 ft-lbs.
Step 2: Tighten Studs 1 through 10 to 50 ft-lbs.
Step 3: Tighten Studs 1 through 10 to 75 ft-lbs.
Step 4: Tighten Studs #11 & #12 to 11 ft-lbs.

with ARP Ultra-Torque fastener assembly lubricant

Bolt Torque Sequence

 11 7 3 1 5 9
12 10 6 2 4 8

Visualizza dettagli completi