Ir directamente a la información del producto
1 de 2

Wagner Tuning

Wagner Tuning Head Stud Kit, BMW M52TU/M54

Wagner Tuning Head Stud Kit, BMW M52TU/M54

Precio habitual $449.99 USD
Precio habitual $449.99 USD Precio de oferta $449.99 USD
Oferta Agotado
Los gastos de envío se calculan en la pantalla de pago.
Coating

BMW M52TU/M54 Engine Pro-Series 18.8 Cylinder Head Stud Set

Replacing the original cylinder head screws with high-strength Pro-Series 18.8 studs is necessary when making large increases in performance, as the original cylinder head screws elongate during operation and the cylinder head can lift off.

The Pro-Series 18.8 stud bolts with a tensile strength of 1850 N / mm² provide a solution to this.

In addition, these stud bolts do not have to be replaced after dismantling, but can be reused.


Kit Contents:

(14) M10 Stud Bolts
(14) M10 Nuts

(14) Washers
Assembly Paste
Assembly Instructions

Tensile strength: PS 18.8 steel / 1850+ N/mm² (270.000+PSI)

A special steel is used which, after tempering, has a tensile strength of 1850 + N / mm².

All threads are formed and not cut as usual. The so-called rolling of threads can increase the strength of the tooth flanks by around 30%.

All Pro-Series products are supplied with a nickel coating or optional with a burnished protecting against corrosion in the long term, even under the toughest conditions. Pro-Series stud bolts have a hexagon socket drive on the head side for screwing in the stud bolts. Due to a cone on the engine block side of the bolt, these are not supported on the thread flanks when the nuts are tightened, but in the bore of the thread in the engine block. This support protects the threads when racing engines are frequently rebuilt.

Pro-Series advantage over other manufacturers is the nuts and washers included in the set, these also have a tensile strength of 1850 N / mm².

Application list:

BMW 320i E46 MY 2000-2007
BMW 325i E46 MY 2000-2007
BMW 330i E46 MY 2000-2007
BMW 520i E39 MY 2000-2003
BMW 520i E60/61 MY 2003-2005
BMW 525i E39 MY 2000-2003
BMW 525i E60/61 MY 2003-2005
BMW 530i E39 MY 2000-2003
BMW 530i E60 MY 2003-2005
BMW 730i/Li E65/66 MY 2003-2005
BMW X3 2.5i E83 MY 2004-2006
BMW X3 3.0i E83 MY 2004-2006
BMW X5 3.0i E53 MY 2000-2006
BMW Z3 2.2i E36/7 MY 2000-2002
BMW Z3 3.0i E36/7/8 MY 2000-2002
BMW Z4 2.2i E85 MY 2003-2005
BMW Z4 2.5i E85 MY 2002-2005
BMW Z4 3.0i E85 MY 2002-2005

Manufactured in Germany

Installation Instructions:

1. After unpacking ProSeries stud bolts, inspect all hardware prior to installation. Look for obvious defects or shipping damage. Contact our sales team immediately with any questions or issues.
2. Before mounting, compare the supplied bolts with the stock screws, paying particular attention to the thread type and length of the bolts.
Check existing threads inside engine block for damage. To ensure proper thread engagement and accurate torque readings, make sure that all threads are free from remnant sealer, lubricant, and debris. Check the flatness and surface finish of the engine block and cylinder head deck to avoid gasket failure.
3. Insert stud bolts into the engine block and tighten with a 5mm hexagon socket on the drive provided at the head of the stud bolt with a torque of 15Nm.
4. If the stud bolts are to remain permanently installed in the engine block, they can be used with screw lock (not included)
5. Attention! Before final mounting of Pro-Series nuts and washers, all contact surfaces must be completely wetted with the supplied special ProSeries lubricant.
If this will not be considered the applied tightening torque is falsified and the resulting clamping force is reduced. Under certain circumstances, this can also inevitably lead to the bolts breaking / shearing off.

6. Tighten nuts in three equal steps in the factory sequence. For the last pass, refer to the table shown below:

Thread Type
M9 x 1.25 1.25 Nm 2.45 Nm 3.65 Nm
M10 x 1.25 1.30 Nm 2.60 Nm 3.85 Nm
M11 x 1.125 1.40 Nm 2.80 Nm 2.80 Nm
M12 x 1.25 1.45 Nm 2.90 Nm 3.130 Nm


7. ProSeries studs and nuts can always be reused. When re-tightening or reassembling, please always ensure that all contact surfaces are wetted with special ProSeries lubricant. Please contact our sales team if you have any further questions.

SKU:WAG-HSK-M54-B

Ver todos los detalles